For info:
UTREC NUMBER: 9707 MANUFACTURER: YODER MANUFACTURING SERIAL NUMBERS: 3781-3782-3828-3833 AGE: 1949 - 1965 SPECIFICATIONS: Hand of Operation: Right to Left Maximum Tube Diameter: 16" (406 mm) Minimum Tube Diameter: 6" (152 mm) Maximum Wall Thickness: .500" (12.7 mm) Maximum Tube Length: 66' (1676 mm) Maximum D/T Ratio: 60:1 Minimum D/T Ratio: 10:1 Maximum Yield: 65,000 PSI Maximum Forming Speed: 150 FPM (45 M) Driven Spindle Diameter: 10" (254 mm) Roll Root Diameter: 19" (482 mm) Gear Box Worm Ratio: 67:1 ENTRY EQUIPMENT: 1- Single Uncoiler 25,000 Lb. (12.5 T) 1 - 9 Roll Flattener 1 - Entry Conveyor (Approx. 30' Long) 1 - Side Edge Trimmer (STAMETS) 1 - Squaring Shear (NIAGRA) 1 - Scrap Chopper, 15 HP (1740 RPM) FORMING MILL: 1 - Pinch Roll 20/25 HP (300-1200 RPM) (32 KW) 4 - Driven Breakdown Stands, 20/25 HP (300-1200 RPM) (32 KW) 3 - Driven Fin Passes, 20/25 HP Each (300-1200 RPM) (32 KW) 3 - Idle Side Roll Units 2 - Cage Forming Section WELD SECTION: 1 - Lead Roll Guide 1 - 4 Roll Weld Pressure 1 - THERMATOOL VT-280 High Frequency Welder, 280 KW x 400 KHZ 1 - AJAX Seam Annealer, 350 KW/1 KC 1 - TOCCO Seam Annealer, 350 KW/1 KC 1 - Pull Out Stand, 25/30 HP (300-1200 RPM) (40 KW) 1 - ID-OD Scarfing Stand COOLANT: 1 - 16' Water Coolant Zone 1 - 100' Air Cool Zone SIZING/SQUARING SECTION: 2 - Driven Sizing Stands, 25/30 HP (300-1200 RPM) (32 KW) 2 - Driven Squaring Stands, 25/30 HP (300-1200 RPM) (32 KW) 2 - Idle Side Rolls 1 - Squaring Turkshead/Straightener FLYING CUT OFF: 1 - Rotary Flying Cut-Off (Round Pipe) 1 - Flying Hot Saw (Square & Rectangle) 1 - Accelerator System NOTE: Rotary cutter & saw fit on the same base. 1 - 70' Run Out Table RE-CUT MACHINE: 1 - BARDONS & OLIVER 16" (406 mm) Rotary Cut-Off Machine NOTE: This machine was used for parting the long lengths. END FACING: 2 - BARDONS & OLIVER 16" (406 mm) Rotary Cut-Off Machines 1 - Complete Conveyor System NOTE: B & O's were used for end champher. HYDROTESTER: 1 - LOEWY Hydro-Tester Maximum Test Pressure: 6500 Lbs. Maximum Pipe Length: 65' Minimum Pipe Length: 14' Testing Range: 8.625" - 16.00" High Pressure Pump: 2 @ 150 HP (1770 RPM) (200 KW) Oil Pump Motors: 2 @ 75 HP (900 RPM) (97 KW) Low Pressure Fill Pump: 200 HP (1760 RPM) (260 KW) PAINTING SYSTEM: 1 - Lacquer Pump & Paint System 1 - Air Dry Conveyor & Inspection Table MISCELLANEOUS EQUIPMENT: 1 - 15 Ton NILES Overhead Crane 1 - 25 Ton PROVINCIAL Overhead Crane 1 - Weight Scale & Marking, 15 Ton Capacity TOOLING: Pipe Round: 16" - 14" - 10" - 8" - 6" Square: 12" x 12" - 10" x 10" - 8" x 8" - 4" - 6" NOTE: There are (2) sets of spindle sets for off line set up. NOTE: All machinery is on it's original foundation and was making X-52 & X-42 grade pipe.