4-1/2" x .187" TUREK & HELLER, TIG, 3" Spdl., 6K# Littell Uncoiler, Flying C/O, 20' Run Out Table *Not Advert.

UTREC NUMBER:    834
MANUFACTURER:    TUREK & HELLER

SPECIFICATIONS:

Maximum Tube Diameter:               4" (102mm)
Minimum Tube Diameter:               .500" (12.7mm)
Maximum Wall Thickness:              .187" (4.75mm)
Minimum Wall Thickness:              .018" (0.5mm)
Maximum D/T Ratio:                   60:1
Minimum D/T Ratio:                   10:1
Maximum Material Yield:              50,000 PSI
Maximum Mill Speed:                  140 I.P.M.
Vertical Adjustment of Driven Stand: 7" - 13" (178mm - 330mm)
Roll Space:                          15" (381mm) Forming
Driven Spindle Diameter:             3" (76mm) High Nickel Alloy Shafts
Roll Root Diameter:                  6" (152mm)
Worm Gear Ratio:                     24:1
Hand of Operation:                   Left to Right
Date of Manufacture:                 1993

ENTRY LINE CONSISTING OF:

6,000 LB LITTELL UNCOILER
  Model:            60-16
  Serial Number:    78629-71
  Expansion Range:  14-3/4" - 20-1/2" (375mm - 521mm)

SHEAR END WELDER:	
  Model:                Hand Type
  Shear:                Hydraulic
  Holddown:             Hydraulic
  Maximum Strip Width:  16" (406mm)

FORMING MILL:
  1- Entry Guide Unit
  5- Driven Breakdown Stands
  5- Idle Side Roll Units
  3- Driven Fin Stands
  1- 20 HP D.C. Motor with 4-Speed Gear Reducer (Breakdown)
  1- 25 HP D.C. Motor with 4-Speed Gear Reducer (Fin)

WELDING SECTION:
  1- Side Closer Seam Guide Unit
  2- Roll Weld Pressure Unit
  1- Belt Sander, Bead Removal, Dual Head Type
  1- Iron Stand Pass
  1- Tig Unit, Miller 400 Amp
  1- Plasma Torch & Power Supply, Thermal Arc

SIZING MILL:	
  3- Driven Sizing Stands with Squaring Fixtures
  2- Idle Side Roll Units
  1- Turkshead Unit, 8-Roll Design
  1- 40 HP D.C. Motor with Gear Reducer (Sizing)

FLYING CUT-OFF SAW:
  Blade Diameter:          26" (406mm)
  Clamping & Accuation:    Hydraulic
  Approximately 100 Spare Cut-Off Blades

RUN OUT TABLE:
  Maximum Tube Length:    20' (6 M)
  Paddle Cylinder:        Hydraulic Kick Off Table

DRIVE ELECTRICS:
  1- Reliance Electric Solid State D.C. Motor Controller
  1- Breakdown Motor 20 HP, D.C.
  1- Fin Motor 25 HP, D.C.
  1- Sizing & Squaring Motor 40 HP, D.C.

MILL PASS ARRANGEMENT:
  1- Breakdown
  2- Idle-Side Roll
  3- Breakdown
  4- Breakdown
  5- Idle-Side Roll
  6- Breakdown
  7- Idle-Side Roll
  8- Fin
  9- Idle
  10- Fin
  11- Idle
  12- Fin
  13- Weld Pressure
  14- Vertical Hold (SR)
  15- Oval Guide
  16- Sizing & Squaring
  17- Sizing & Squaring
  18- Sizing & Squaring
  19- Turkshead 8-Roll
						
TOOLING - To Produce the Following Sizes:
  2-1/2" 	(63.5mm) 	Round
  3-1/8" 	(79.3mm) 	Round
  2-1/2" 	(63.5mm) 	Square
  3" x 2" 	(76.2mm x 50.8mm) Rectangular
  2-3/4" 	(69.8mm) 	Round
  3-3/4" 	(95.2mm) 	Round
  3" 		(76.2mm) 	Square
  2" x 4" 	(50.8mm x 101.6mm) Rectangular
  3" 		(76.2mm) 	Round

All tooling is believed to be complete, however, an inspection is recommended.

CONDITION:	Very Good