3" (76 mm) x .095" (2.4 mm) YODER #M2 TIG Tube Mill

UTREC NUMBER:  1454
MANUFACTURER:  YODER
MODEL NUMBER:  M2
SERIAL NUMBER: Y8496-995
AGE:           1996
SPECIFICATIONS:
Hand of Operation:          Right to Left
Maximum Tube Diameter:     3" (76 mm)
Minimum Tube Diameter:     1/2" 
Maximum Wall Thickness:    .095" (2.4 mm)
Minimum Wall Thickness:    .020" 
Maximum Line Speed:        25 FPM 
Maximum D/T Ratio:         60:1
Minimum D/T Ratio:         10:1
Maximum Material Yield:    50,000 PSI

GEAR BOX DATA:
  Spindle Diameter:         2-1/2" 
  Roll Space Forming:       15"
  Roll Space Fin & Size:    9" 
  Horizontal Centers:       18" (457mm) Forming
                            15" (381mm) Fin & Sizing

ENTRY EQUIPMENT:
1 - Double Uncoiler, 4,000 Lbs.
1 - Shear End Welder, TIG, Built by LEE SCHAFFER, MILLER Welder

FORMING MILL:
4 - Driven Breakdown Stands
4 - Idle Side Rolls
3 - Driven Fin Stands
3 - Idle Side Roll Units

WELDING SECTION:
1 - THERMATOOL OLIMPIA 80 2 Roll TIG Weld Pressure Unit
1 - SUBURBAN Automatic Controls Weld Power Distribution Panel
3 - NERTINOX TH300 Welders
1 - Tri-Cathode Torch SAF
1 - SAF Solid State Weld Control
1 - Gas Mixter & Weld Station
Coolant Section
1 - Periscope Site for Viewing Weld Pool

SIZING MILL:
3 - Driven Sizing Stands
3 - Idle Side Rolls
1 - Straightener, Turkshead

CUT OFF:
1 - CLEARING USI Cut Off Press w/Accelerator & Die Set w/Spares
     Serial Number:    57-724
     Series Number:    45T640533
     Strokes/Min.:     100
     Stroke:           4"
     Shut Height:      15"
     Slide Adjustment: 2-1/2"
1 - 20' Run-Out Table

MILL DRIVE:
1 - EUROTHERM D.C. Drive System w/ 3 EUROTHERM 590 Series Digital Drives
1 - 15 HP EUROTHERM Forming Motor, 1150/2000 RPM, Shunt Wound 5000 
     Armature D.C. Motor
1 - 10 HP - Fin Motor
1 - 10 HP - Sizing Motor
1 - PLC Control & Operator Station w/ALLEN BRADLEY SLC/500 PLC
      Voltage 480/3/60

TOOLING TO PRODUCE THE FOLLOWING ROUND SIZES:
7/8"		1.875"		47.6mm
1"			1.00"		25.4mm
1.067"		1.067"		27.1mm
1-1/8"		1.125"		28.6mm
1-3/8"		1.375"		34.9mm
1-1/4"		1.250"		31.8mm
1-1/2"		1.500"		38.1mm
1-5/8"		1.625"		41.3mm
1-3/4"		1.750"		44.5mm
1-7/8"		1.875"		47.6mm
2"			2.00"		50.8mm
2-1/4"		2.250"		57.2mm
2-1/2"		2.500"		63.5mm
3"			3.00"		76.2mm

EXTRA ITEMS:
1 - Lot Spare Parts, Gearbox, Spindles, Bearings and Gears
1 - Safety Curtain w/E-Stop
1 - Mill Coolant System
1 - Spare 15 H.P. G.E. D.C. Motor for Forming Section
1 - Spare 7.5 H.P. G.E. D.C. Motor for Fin or Sizing Section

Condition:	Very Good As Taken From Service, Under Power Running.
Complete Electrical and Mechanical Drawings