YODER W35 Form & Weld Square H.F. Tube Mill

UTREC NUMBER:    1478
MANUFACTURER:    YODER MANUFACTURING
MODEL NUMBER:    W35
SERIAL NUMBER:   Y3915-65
SPECIFICATIONS:
Line Speed:                30 - 150 FPM
Entry Line Speed:          30 - 300 FPM
Max. Material Thickness:   .238" (6mm)
Hand of Operation:         Left to Right

Entry Line:
Coil Storage Ramp:        4 Coils
Coil Car, Floor L-Type:   16,000 Lbs. (8 T), S/N: 2099
YODER Mandrel-Type Uncoiler, S/N: Y-2100:
  Sliding Base
  Hold Down Roll, S/N: 2101
  Hydraulic Expansion
  I.D. Range: 20" - 24"
Over-Under Peeler

YODER 5-Roll Flattener, S/N: Y-2102
  Entry Pinch Rolls
  25 HP Motor

Shear & End Welder, S/N: Y-2104
  Hydraulic Shear
  Manual Weld Clamp

YODER Overhead Looping System, S/N: Y-2105
  Type: 4 Strand
  Clamping
  Winch - D.C. Drive
  Pull Out Stand, 25 HP, D.C.
  Total Length 120' x 4 Strand
  Approximate Storage of Strip 500'

Pre-Punch Press, S/N: 2109
  Mfg.:       NIAGARA
  Model:      B5-1/2-96
  Bed Length: 96"
  Digital Press Feeder, S/N: 2108

Forming Mill, S/N: Y2110
  Entry Guide Unit
  (7) Break Down Stands (Driven)
  (3) Fin Stands (Driven)
  (7) Idle Side Roll Units
  Roll Space:  Forming:  20"
               Fin:      11"
  Shaft Diameter:        4"
  Vertical Adjustment:   7-15/16" - 13-3/8"
  Horizontal Centers:    20"

Welding Section:
  (2) Roll Pre-Weld Station
  (4) Roll Weld Pressure
  Dual Scarfing Unit
  Seam Iron Pass
  High Frequency Welder, S/N: Y-2111:
    Mfg.:          THERMATOOL
    Model:         VT-160
    Serial Number: 1237 (1986)
    Frequency:     400 KC
    SCR Type
    Single Tube & Choke
    Contact Welding
	
Flood Type Coolant Zone
 Length: 8'

Sizing Mill, S/N: Y-2112
  (3) Driven Sizing Stands
  (3) Idle Sizing Stands
  (1) Single Plane Turkshead
  Roll Space:          11"
  Shaft Diameter:      4"
  Vertical Adjustment: 7-15/16" - 13-3/8"
  Horizontal Centers:  20"

Flying Cut-Off Press, S/N: Y-2113:
  Mfg.:     NIAGARA
  Capacity: 200 Ton
  Model:    B1-6-1/2
  Flying Die Accelerator
  (1) Auto Stacker & Package Unit
  (1) Run-Out Dump Table Assembly, S/N: Y-2114

Drive Electrics:
  Pinch Roll:  24 H.P. D.C.
  Forming:     75 H.P. D.C.
  Sizing:      60 H.P. D.C.

Note: D.C. Drive Was Replaced in 1996 By Galco, S/O No. 2021271,
      QUANTUM 111 Digital Drive System.

Coolant Tank w/Re-circ Pumps
  10' x 8' x 4' H

Pass Arrangement:
  Forming:
   Breakdown
   Idle
   Breakdown
   Idle
   Breakdown
   Breakdown
   Idle
   Breakdown
   Idle
   Breakdown
   Idle
   Fin
   Idle
   Fin
   Idle
   Fin
   L/R Seam Guide
   4 Roll Work Pass
   Dual Scarf
   Seam Iron

  Sizing:
   Size	
   Idle
   Size
   Idle
   Size
   Straight