24" x 7.5" x 15,000# Seco Slitting Line

ENTRY COIL SIZE:

WIDTH:                 2" TO 25.5"
THICKNESS:             0.012" TO 0.220"
INSIDE DIAMETER:       16" MIN./28" MAX.
OUTSIDE DIAMETER:      60"

EXIT COIL SIZE:

WIDTH:                  0.3125" TO 24.75"
INSIDE DIAMETER:        16" - 18" - 20" - 24"
OUTSIDE DIAMETER:       60"

LINE SPEED:             MINIMUM 125 FPM
                        MAXIMUM 1300 FPM (BUILD UP SPEED)
LINE DIRECTION:         RIGHT TO LEFT

SLITTING CAPACITY:

.195" TO .220" - 5 CUTS MAX. (1" WIDE & OVER)
.156" TO .195" - 9 CUTS MAX. (0.75" WIDE & OVER)
.125" TO .156" - 11 CUTS MAX. (0.625" WIDE & OVER)
.070" TO .125" - 11 CUTS MAX. (0.375" WIDE & OVER)
.040" TO .090" - 11 CUTS MAX. (0.312" WIDE & OVER)
.030" TO .070" - 13 CUTS MAX. (0.375" WIDE & OVER)
.015" TO .030" - 15 CUTS MAX. (0.75" WIDE & OVER)
.012" TO .014" - 13 CUTS MAX. (1.25" WIDE & OVER)

CONSISTING OF THE FOLLOWING:

-ENTRY COIL LIFT
  PIT TYPE
  HYDRAULIC CYLINDER LIFT
   6" DIA. BORE X 19" STROKE

-UNCOILER:
  HYDRAULIC "LINK TYPE" EXPANSION
  16" - 22" I.D. W/28" PADS
  3 SEGMENT MANDREL
  SLIDING BASE
  HYD. CYLINDER OPERATED DRAG BRAKE
  AC MOTOR THREADING DRIVE
  DRIVEN HOLDDOWN ROLL

-SLITTER HEAD
  7.5" DIA. X 26" FACE ARBORS
  ENTRY TENSION PAD
   HYDRAULIC CYLINDER LOADED
  ENTRY DRIVEN PINCH ROLLS
   6" DIA. X 28" FACE WIDTH
  ENTRY ROLLER SIDE GUIDES
   MANUAL ADJUSTMENT
  PARALLEL ADJUSTMENT OF TOP ARBOR
  EXIT PASSLINE ROLLS
   4" DIA. X 38" FACE WIDTH
  75/100 HP WESTINGHOUSE DC MOTOR
   400/1600 RPM, 230 V
  HORSBURGH & SCOTT REDUCER WITH 8.2:1 RATIO
  FAWICK AIR OPERATED SLIP CLUTCH
   #11.5VC-500

-SCRAP BALLER
  24" WIDE BALL CAPACITY
  AC MOTOR DRIVE

-RECOILER
  COMMON DRIVE WITH SLITTER HEAD
  16", 18", 20" AND 24" DIA. X 30" FACE DRUMS
  MECHANICAL CLAMP AND EXPANSION
  OVERARM SEPARATOR
  HORSBURGH & SCOTT REDUCER WITH 10.25:1 RATIO
  FAWICK AIR OPERATED WATER COOLED SLIP CLUTCH
   DUAL #16VC-600
  APPROX. 36" FROM FLOOR TO CENTER OF DRUM

-EXIT COIL CAR W/STRIPPER PLATE
  PIT TYPE
  HYDRAULIC CYLINDER LIFT
   5" DIA. BORE X 18" STROKE
  HYDRAULIC CYLINDER FOR STRIPPER PLATE
   3.25" DIA. BORE X 23" STROKE
  HYDRAULIC CYLINDER TRAVERSE
   4" DIA. BORE X 42" STROKE

-HYDRAULIC POWER UNIT
  7.5 HP AC MOTOR
  1165 RPM, 208-220/440 V
  VICKERS PUMP

-TOOLING INCLUDED: KNIVES, SPACERS AND RUBBERS
    TOOLING SIZES:  7.5" ID X 11.8" OD KNIVES, Max OD on the tooling is 12"
                   (41) .220", (67) .250", (43) .300",
                   (40) .350", (33) .360", (47) .460" WIDTHS

-COMPLETE DRAWINGS INCLUDED

-IN STORAGE