For info:
SPECIFICATIONS: Max. Tube Diameter: 3.0" (76.2 mm) Min. Tube Diameter: .500" (12.7 mm) Max. Wall Thickness: .148" (3.7 mm) Min. Wall Thickness: .032" (0.8 mm) Max. D/T Ratio: 60:1 Min. D/T Ratio: 10:1 Max. Material Yield: 50,000 PSI Max. Mill Speed: 250 FPM (80 M) Roll Space (Width) Forming: 11.000" (280 mm) Roll Space (Width) Fin & Sizing: 4.500" (114 mm) Driven Spindle Diameter: 2.5" (63.5 mm) Hand of Operation: Left to Right ENTRY EQUIPMENT (new and reconditioned) 1- Double 6,000 Lb. Uncoiler, manual expansion and rotation 1- Guild Model PSA, Shear End Welder, complete self contained (new) 1- Strip Storage Accumulator, 1250 Ft. of strip storage 1- Complete Entry Line Electrical Equipment FORMING MILL (new) 1- Entry Guide Unit 3- Driven Breakdown Stands, with transmissions 4- Idle Side Roll Units (Cluster unit, 4 pass) 2- Driven Fin Stands, with transmissions 1- Idle Side Roll Unit 1- (New) 60HP DC Motor and Solid State Reliance Controls 1- New Operators Control Desk WELDING SECTION (new) 1- Side Closer Seam Guide Unit 4- Roll Weld Pressure Unit 1- Scarfing and Seam ironer Unit 1- Bead Winder 1- Thermatool Model TMI 150, 450kc, High Frequency Induction Welder COOLANT SECTION (new) 1- 20Ft. (6M) Coolant Zone, Spray Type System SIZING MILL (Rebuilt) 3- Driven Sizing Stands, with transmissions, (2 stands are new) 3- Idle Side Roll Units 1- Straightener Unit (Modified Turkshead) 1- (New) 60 HP DC Motor and Solid State Reliance Controls, new operators control station TUBE CUT OFF SYSTEM 1- Alpha Model SR12 High Speed Cut Off Press, with electrical cabinet (reconditioned) 1- Talleyrand, Hydraulic, Digital Length Control System, Mounted on Press (new) 1- Single dump, pneumatic accuated Run-Out-Table, Maximum length, 7Meters (new) ELECTRICAL (new) 1- Reliance, solid state, DC Drive System, complete, NEMA enclosure, separate power Module for each DC 60HP Motor. Three door electrical cabinet Abbey Design. 1- Emergency Stop, safety stop cable and interface, mounted on the mill. 1- Operator control station with all necessary Mill controls, digital readouts, Forming and Sizing trim pots, E-Stop, MPM indicator, and Motor current indicator each DC motor. 1- Transformer 380 VAC primary to 460 VAC secondary 50/60Hz. MILL PASS ARRANGEMENT 1- Driven Breakdown 11- Side Closer, Seam Guide 2- Driven Breakdown 12- 4-Roll Weld Pressure 3- Driven Breakdown 13- Scarfing/Seam Ironer 4- Idle Side Roll 14- Idle Side Roll 5- Idle Side Roll 15- Driven Sizing 6- Idle Side Roll 16- Idle Side Roll 7- Idle Side Roll 17- Driven Sizing 8- Driven Fin 18- Idle Side Roll 9- Idle Side Roll 19- Driven Sizing 10- Driven Fin 20- Idle Straightener (Modified Turkshead) TOOLING No tooling is included in this quotation. DRAWINGS 1- Complete set of Electrical and Mechanical drawings. All necessary installation drawings. 1- All necessary catalogs for all equipment purchased with this line. CONDITION: Like New , (Rebuilt by Abbey Etna 1994, 1-year warranty)