For info:
Date of Manufacture: 1983 MILL SPECIFICATIONS: Maximum Tube Diameter: 6-5/8" (168 mm) Minimum Tube Diameter: 2" (50.8 mm) Maximum Wall Thickness: .250" (6 mm) Minimum Wall Thickness: .060" (1.5 mm) Maximum D/T Ratio: 60:1 Minimum D/T Ratio: 10:1 Maximum Material Yield: 50,000 PSI Maximum Mill Speed: 200 FPM (60 M) High Gear, 100 FPM (30 M) Low Gear Roll Space Forming: 23" (600 mm) Roll Space Fin & Sizing: 10" (254 mm) Driven Spindle Diameter: 4.3" (110 mm) Hand of Operation: Right to Left Spur Gear Ratios in Breakdown Stands: (#1) 1.7:1, (#2) 2.1:1, (#3) 2.7:1, (#4) 2.7:1, (#5) 2.7:1 ENTRY EQUIPMENT: 1 - 20,000 Lb. Uncoiler, 60" O.D. X 16"-20" I.D. 1 - Coil Car, 20,000 Lb. Capacity With Hydraulic Push On 1 - Automatic Shear End Welder, Complete Self-Contained, with MIG Welding 1 - 5-Roll Flattener, Driven, With Quick Lift 1 - 2-Roll Pinch Roll, 60 HP DC 1 - Floop, Vertical Strip Accumulator Maximum Strip Width: 21" (533 mm) FORMING MILL: 1 - Entry Guide Unit With Edge Condition 5 - Driven Breakdown Stands, with Gear Boxes, and Universal Joints 2 - Idle Side Roll Units 3 - Driven Fin Stands, with Gear Boxes and Universals 1 - Idle Side Roll Unit 1 - 150 HP DC Motor (110 KW) With 2 Speed Shift Gear Box WELDING SECTION: 1 - Seam Guide Lead Roll 1 - 4 Roll Weld Pressure Unit 1 - Double Scarfing Unit With Quick Lift 1 - Bead Winder 1 - 400 KW Electroheating High Frequency Welder Complete With Heat Exchanger COOLANT SECTION: 1 - 20' Coolant Zone, Flood Type System SIZING MILL: 4 - Driven Sizing Stands, with Gear Boxes, and Universal Joints 4 - Idle Side Roll Units 2 - Squaring Turkshead 1 - 150 HP DC Motor (110 KW) With 2 Speed Shift Box FLYING CUT-OFF SYSTEM: 1 - 3 Disc Rotary Cut-Off Flying Hot Saw 1 - Digital Length Control System 1 - 24 Foot, Single Dump Run-Out-Table NOTE: Rotary Cut-Off Lifts Off And Flying Saw Fits On Existing Traveling Base Via Quick Disconnect PASS ARRANGEMENT: 1. Breakdown 12. Fin 23. Size 2. Breakdown 13. Fin 24. Idle 3. Breakdown 14. Lead Roll 25. Size 4. Idle 15. Preform 26. T-Head 5. Breakdown 16. Weld Pressure 27. T-Head 6. Idle 17. I.P. 28. T-Head 7. Breakdown 18. Oval Guide 8. Idle 19. Size 9. Idle 20. Idle 10. Idle Side Roll 21. Size 11. Fin 22. Idle MOTORS AND DRIVE SYSTEM: 1 - Pinch Roll, 60 HP DC (45 KW) 1 - Forming Motor 150 HP DC (110 KW) 1 - Sizing Motor 150 HP DC (110 KW) 1 - Solid State Control Package, Thyrister Controlled TOOLING To Produce The Following Sizes: Round Tube: O.D.: 2-1/2, 3", 4", 5" and 6-5/8" N.B.: 2", 3", 4", 5" and 6" Square Tube: 2" x 2", 2-1/2" x 2-1/2", 3" x 3", 3-1/2" x 3-1/2", 4" x 4" and 5" x 5" Rectangle Tube: 2-1/2" x 1-1/2", 3" x 1-1/2", 3" x 2", 4" x 2", 4" x 3", 5" x 2", 5" x 3", 6" x 2", 6" x 3" and 6" x 4" Maximum Ratio of Rectangle 3:1 DRAWINGS: 1 - Complete Set of Electrical and Mechanical Drawings. All Necessary Installation Drawings. CONDITION: Very Good, Under Power, Singapore