For info:
SHIGIYA 2 Axis CNC Conversational Cylindrical Grinder CNC Control ............................ Fanuc PowerMate-D Capacity: Swing over the table ................... 11.8" Maximum center distance ................ 39.4" Maximum grinding diameter .............. 11.8" Distance to the center of workpiece from front of the machine .............. 13.4" Center hight from floor ................ 41.3" Wheel slide angle ...................... 90 degrees Wheelhead: Total traverse amount .................. 9.6" Rapid infeed amount (CNC controlled) ... 1.57" Wheelhead swivel ....................... N/A Minimum increment ...................... .00001 inch/diameter Manual over ride ....................... x1, x10, x100 of .00001 inch Jog speed over ride .................... 0 to 150 % of 50 inch/min.(10% steps) Rapid speed over ride .................. 0%, 25%, 50%, 100% of 200 inch/min. Infeed speed over ride ................. 0 to 150% of programmed speed Wheel speed change ..................... N/A Wheel spindle speed .................... 1546 rpm Wheel surface speed .................... 6450 ft/min. at 16 inch wheel Wheel flange capacity: Maximum wheel size ..................... 16" Maximum wheel width .................... 2" with type 1 wheel 3" with type 7 wheel Minimum wheel width .................... 1" with type 1 wheel Wheel bore size ........................ 5" Wheel motor ............................ 5 HP Wheel infeed motor ..................... 1.2 HP (AC servo) Table: Swivel capability Tailstock toward wheelhead (C.C.W.) .... 9 degrees Tailstock toward operator (C.W.) ....... 0 degrees Total traverse amount .................. 28.0" Minimum increment ...................... .00001" Manual over ride ....................... x1, x10, x100 of .00001" Jog speed over ride ................... 0 to 150 % of 100 inch/min.(10% steps) Rapid speed over ride .................. 0%, 25%, 50%, 100% of 275 inch/min. Infeed speed over ride ................. 0 to 150% of programmed speed Workhead: Spindle Dead center workhead spindle Speed range ............................ 15 to 600 rpm Programmable 1 rpm step Center specification ................... Morse taper #4 Through hole size ...................... 0.93" Workhead motor ......................... 2 HP (AC servo) Tailstock: Activation ............................. Manual lever type Total movement ......................... 1.18" Fine taper adjustment .................. N/A Taper .................................. Morse taper #4 Tank: Hydraulic .............................. 8.9 gallon Pump ................................... 0.5 HP Wheel lubrication ...................... 3.2 gallon Pump ................................... 1/4 HP Coolant ................................ 31.5 gallon Pump ................................... 1/4 HP Conversational Program: Method of programming .................. On screen "Teach" type Maximum diameters within 1 program ..... Up to 7 diameter Maximum storage memory in the machine .. Up to 10 programs Dressing patterns ...................... 4 patterns Grinding patterns ...................... 7 patterns Grinding condition ..................... Automatic calculation (editable) Dressing condition ..................... Automatic calculation (editable) Machine features * Base of machine - High stability, strategically ribbed cast iron base for optimum vibration damping * Wheelhead - Single piece cast iron wheelhead unit for rigidity * Wheel spindle - Hydro-dynamic bearing spindle for rigidity and vibration damping * Hand scraped slide ways - Continuous oil film slide ways for maximum built-in and long life accuracy * Hi-resolution AC servo motor encoder - Hi-accuracy positioning and low vibration * Infinitely variable speed workhead - CNC controlled AC servo motor * Manual tailstock - with retract lock * Sub-table mounted wheel dresser - Diamond reference unrelated to table swivel * Hydraulic tank and pump - Isolated from machine base for minimizing heat effecting and vibration effecting * Coolant tank and pump - The standard tank has 4 sections for cleaning dirty coolant * Machine color: Munsell 5Y6/1 Standard equipment 1 set Wheel flange 1 pc. Wheel flange puller 2 pcs. Carbide tipped center 1 set Setup tools 1 pc. Setup tool box 1 set Diamond tool holder 1 set Wheel spindle lubrication tank 1 set Front coolant splash cover 1 set Hydraulic tank 1 set Coolant tank & pump 1 set Coolant splash cover 1 set Leveling pads and bolts Floor space (Width x Depth x Hight) 14.4x 6.5 x 5.8 feet Machine weight 7920 lbs..